Garage Door Repair Installation Apex, NC

A broken spring on the overhead garage door was replaced, and the legacy chain drive motor was serviced. The broken spring was carefully removed and replaced with a new one, ensuring the door's safety and functionality. The chain drive motor was inspected, lubricated, and adjusted as needed to ensure smooth and quiet operation. The door was tested to confirm that it was functioning correctly, and any necessary adjustments were made. The job was completed with attention to detail and a commitment to quality.

A Clopay door, previously damaged by a car collision, was meticulously repaired. The door's structural integrity was restored, ensuring it functioned smoothly. The Chin Drive LiftMaster motor was serviced to guarantee optimal performance. This involved inspecting and replacing any worn components, lubricating moving parts, and testing the motor's operation. The door was then reassembled, and its alignment was checked to ensure it opened and closed without obstruction. Safety checks were conducted to confirm the door's secure operation. The job was completed with precision, restoring the door to its original condition.

Did a service for a single two car, metal garage door and craftsman operator.

Sent out to look at a genie garage door operator for repair or replacement.

Replace an old chamberlain operator with a new LiftMaster chain operator.

Gave an estimate for replacement of bottom, rubber and retainer on their single two car metal garage door.

Installed a new LiftMaster 6580L – 7 foot belt.

Operator loss settings due to power flickering on and off had to set genie operator back up so that it would work proper service for a single two car insulated garage door.

Replaced bottom rubber ,and retainer seal at bottom of garage door and replaced trim around garage door and ,replaced garage door operator.

Replaced regular bracket with an adjustable bracket on a single two car metal garage door.

Converted the Wayne Dalton, garage door, torque master spring system to torsion Springs.

I successfully completed a torsion spring conversion on a Wayne Dalton garage door, ensuring the door operates smoothly and safely. This involved removing the old springs and installing new ones, adjusting the tension to match the door's weight, and testing the door to confirm proper functionality. Additionally, I serviced a LiftMaster belt drive garage door opener. This included inspecting and lubricating the belt, checking the motor and sensors for optimal performance, and testing the opener to ensure it opens and closes the door reliably. Both systems now function efficiently, providing peace of mind and convenience.

Replace broken torsion springs on a single two car insulated garage door.

A garage door that had been struck by a car required immediate attention. First, I assessed the damage to the door, ensuring safety and functionality. The impact had caused misalignment and potential structural damage. I carefully realigned the door and secured it to prevent further issues. Next, I focused on the LiftMaster belt drive motor. I inspected the motor for any damage or wear caused by the incident. After confirming the motor was operational, I performed a thorough cleaning and lubrication to ensure smooth and efficient performance. Finally, I tested the entire system to guarantee the door operated correctly and safely. This comprehensive repair restored the garage door to its optimal condition.

Replaced a broken torsion spring on a single two car Wayne Dalton garage door.

Replaced their old LiftMaster keypad with a new one.

A recent project involved replacing an existing overhead door with a modern DoorLink garage door. The new installation featured a LiftMaster 6586L, a high-performance garage door opener known for its reliability and advanced features. The process began with the careful removal of the old door, followed by the precise installation of the new DoorLink system. The LiftMaster 6586L was then expertly installed, ensuring seamless integration with the new door. A thorough safety check was conducted to verify that all components were functioning correctly and safely. This included testing the automatic reverse feature, checking the sensitivity of the sensors, and ensuring the door operated smoothly. The project was completed to the highest standards, enhancing both the functionality and security of the garage.

Service for a single one car, metal garage door replaced trim and replaced rollers

Serve a single two car insulated garage door and LiftMaster garage door operator was called to fix noise. Found that roller at bottom was striking bolt on track. Had to adjust as needed.

Replace an old garage door opener with a new LiftMaster chain drive.

Service needed on a single two car, metal garage door and their logic board need to replaced on their LiftMaster garage door opener.

Replaced a broken torsion spring on a single two car metal garage door

Replaced broken torsion springs on a single two car insulated garage door.

performing a garage door repair on an insulated Overhead Door. door had fell out of the track. servicing a Genie garage door operator.

Replaced Wayne dalton garage door with hörmann garage door. Also serviced liftmaster motor and performed safety inspection.