Question 1

How do I know what size garage door I have or need?

Accepted Answer

Measure the width of the actual finished opening and then the height. Garage door sizes are always shown and listed as the width first and then the height. In addition, we provide free in house estimates and will measure the opening for you while we are at your home or project site to determine the proper size.

Question 2

How do I release the door from the operator so that I can open the garage door by hand?

Accepted Answer

With the garage door fully closed, simply pull the red release cord down toward the floor and back towards the operator. Always take special caution whenever you release the garage door opener if the door is not in the fully closed position, since the door may want to slam closed when released. If at all possible do not release the garage door when open, except for emergency or security purposes, and close the door with caution. Some older openers may not have a red release cord and may need to be released by pulling down a handle, a spring-loaded clip, or even possibly unbolting the arm from the door and opener. If you do have an older door that is difficult to disconnect you may want to replace the opener with a new garage door opener that has an easy-pull red release cord.

Question 3

How can I tell if the garage door spring is balanced properly?

Accepted Answer

Open the door halfway by hand (release operator first) and let go of the door. The door should pretty much stay in the same position, although some slight drifting may occur. If the door wants to drop or if it opens on its own the garage door springs should be adjusted by trained and experienced garage door service technicians. To avoid possible severe injuries do not attempt to adjust the springs yourself without having the proper training and tools.

Question 4

We heard a loud noise in the garage and have not been able to open the garage door since we heard the noise. What could possibly be wrong with the door?

Accepted Answer

It is very highly likely that you have a broken spring that should be replaced by an experienced and qualified garage door service technician. If your springs (torsion springs) are on a shaft across the top of the door, you will see an approximate 2″ separation in the spring. If your springs (extension springs) stretch along the track on the sides you will find that they are very obviously in two separate pieces.

Question 5

I have two springs on a shaft across the top of the door and one of the springs is broken. How do I know if I should change both springs or just the one spring that is broken?

Accepted Answer

We highly recommend that you change both springs at the same time since both springs have been under the same amount of stress each time the door has been opened and closed. Unfortunately, a visual inspection of the spring can not determine the further life expectancy of the spring. In many cases, it will cost less to have both springs changed at the same time than if you only had one spring changed at a time. In addition, if you have extension springs on your door, the door may not balance properly with one new spring and one fatigued spring. Place a service order today to have both springs replaced and get your door back in proper working order!

Question 6

My spring broke very close to the end of the spring. Can I just throw away the part that broke off and reuse the rest of the old spring without having any problems?

Accepted Answer

The remaining unbroken part of the spring should never be reused. Not only is the old spring fatigued for the full length of the spring and could easily break again at any moment, changing the length of the spring will also distort the lifting power of the spring and will not balance the weight of the garage door properly. Do not attempt to replace the spring yourself; instead, have it changed by a qualified service technician.

Question 7

Our garage door opener will not do anything at all when we push the button. What should we look for first?

Accepted Answer

The first thing that you should verify is that the opener is still plugged into the electric outlet. Next, you should confirm that there is power coming out of the electric outlet or plug the opener into another outlet with a temporary extension cord. If there is power to the operator then there is some type of mechanical or electrical problem within the garage door opener itself. It needs to be diagnosed by a qualified service technician.

Question 8

The light comes on but the garage door opener will not open or close the door. What should we look at first?

Accepted Answer

If the light on the garage door opener comes on, the opener is getting power and therefore the problem would be in the electrical or mechanical workings of the opener. Be sure to unplug the operator before making any attempt to remove the motor head cover. To avoid the possibility of electrical shock, have your garage door opener repair made by a knowledgeable service tech. If your garage door opener is more than ten years old you may want to consider replacing the garage door opener to one with the latest safety features.

Question 9

Both of our transmitters quit working at the same time. Should we try changing the batteries in the remote controls?

Accepted Answer

Very seldom will the batteries in both transmitters go dead at the same time. Most likely the problem is in the radio receiver that is in the garage. It is also possible that the problem could be inside the operator itself and that it is no longer sending power to the receiver unit. (On some openers the receiver and logic board are combined together on one solid-state circuit board). It may be to your advantage to have a professional service call to determine the true problem.

Question 10

Our garage door opener was working fine, but all of a sudden we have to hold the wall button down to get the door to close. How can we get the door opener to start working properly again?

Accepted Answer

It sounds like the photo-cell safety beams are blocked, misaligned, or malfunctioning. Move any objects that may be interfering with the signal and verify that the photo-cell LED lights are illuminated as per the manufacturer’s instructions. (The photo-cells can not be permanently removed from garage door openers that were built since 1973). If the infrared beams are not blocked and the photo-cells appear that they are aligned, then contact us to diagnose and repair the problem. You will not be able to close the door with the remote control transmitter until the photo-cells are in proper working order.

Question 11

While we were closing the overhead garage door something caused the door to stop halfway and now the door is hanging crooked in the opening. What is wrong with the door?

Accepted Answer

Most likely one of the garage door cables has come off of the cable drum (the side that is hanging the lowest) from closing on something. The cables may still be under spring tension and should not be touched without the proper knowledge and tools to make the repair.

Question 12

The two bottom sections of our garage door were damaged by a car bumping into the door. Can the two sections be replaced?

Accepted Answer

Yes, the two bottom sections can be replaced as long as the sections are still available (many older garage doors have sections that are no longer made and it may be very difficult to find an exact match). However, in many cases, the cost of the two sections and the labor to replace them may be very close to the cost of a brand new replacement garage door that will have all new track, springs, and hardware included along with the door sections.

Question 13

The cable on the garage door appears to be fraying. Should we be very concerned about this problem?

Accepted Answer

Your amount of concern should depend upon how much the cable is frayed, although the problem will only continue to get worse. If the cable is severely frayed to where there are only a few strands left that could break at any moment, the cable should be replaced by a qualified garage door service technician as soon as possible.

Sitemap

Pages

ClipIt Coupons